Camera Settings

What ISO to Use for Landscape Photography

Use base ISO, usually 100, on a tripod for the cleanest files. Learn when raising ISO helps with handheld shots, moving foliage, and night skies.

On this page
  1. Why base ISO gives the cleanest files
  2. Finding your camera’s base ISO
  3. How ISO works
  4. When to raise ISO
  5. Modern sensors and ISO invariance
  6. Noise and AI denoise
  7. Long exposures and noise reduction
  8. Common misconceptions

On a tripod, use your camera’s base ISO, usually 100. Raise ISO only when you need a faster shutter speed to freeze movement, or when you have to handhold in low light. Base ISO gives the most dynamic range and the least noise, so it is the default for a still landscape.

Why base ISO gives the cleanest files

Base ISO gives the most dynamic range, often 12 to 15 stops on modern sensors (the figure varies by model), and the least noise. That range lets you recover shadows and highlights in editing. Each step up in ISO usually reduces dynamic range a little.

Finding your camera’s base ISO

Base ISO varies by camera. Many bodies use 100. Some Nikon Z7, Z8, and D850 bodies start at 64, and many Fujifilm bodies start at 125 to 160. Check your manual or the ISO menu.

Extended settings such as Lo ISO 50 are usually base ISO pulled down, with less highlight headroom. They are not cleaner, so avoid them for high-contrast scenes.

How ISO works

ISO does not change how much light the sensor captures. Aperture and shutter speed set that. ISO applies gain to the signal from the sensor. Each doubling, such as 100 to 200, lets you use one stop less light for the same exposure, but it usually costs some dynamic range.

When to raise ISO

  • Handheld landscapes: raise ISO to about 400 to 1600 to keep the shutter at or above 1/(focal length × crop factor).
  • Wind-blown foliage on a tripod: about 400 to 800 can reach 1/125 s or faster.
  • Milky Way: typically ISO 1600 to 6400 at f/1.4 to f/2.8 for 10 to 25 seconds.

Do not hold ISO at 100 if that costs you a sharp frame. A sharp image at a higher ISO is usually the better result.

Modern sensors and ISO invariance

Many modern sensors are close to ISO-invariant. That means an underexposed raw file brightened later can look similar to one shot at a higher ISO. How close this is depends on the model.

Dual-gain sensors often show a noise drop at a second native ISO, around 400 to 800 on some Sony, Nikon, and Canon bodies. Test your own camera before you rely on either approach.

Noise and AI denoise

Noise comes mostly from too little light, so ISO is a symptom of the exposure rather than the cause. Exposing at a higher ISO often gives cleaner shadows than underexposing at base ISO and pushing the file later. Do not underexpose just to keep ISO low.

AI denoising tools, such as Lightroom Denoise, DxO PureRAW, and Topaz, make raw files shot at ISO 3200 to 6400 far more usable.

Long exposures and noise reduction

Long-exposure noise reduction takes a dark frame as long as the exposure, so the total time doubles. A two-minute exposure takes about four minutes. Many photographers turn it off and rely on editing noise reduction instead.

Common misconceptions

  • “ISO changes sensor sensitivity.” It applies gain after capture. Aperture and shutter set how much light is collected.
  • “Always use ISO 100, whatever the conditions.” Handheld or windy scenes may need a higher ISO for sharpness.
  • “Lo ISO is cleaner than base ISO.” It usually reduces dynamic range.
  • “High ISO causes noise.” Noise comes mostly from too little light.

For the wider settings, see the best camera settings for landscape photography. For the shutter speeds that set how much ISO you need, see what is a good shutter speed for outdoor photography?

The complete guide to camera settings

The Best Camera Settings for Landscape Photography
Read the guide

Keep exploring

Guides from other topics

All topics →